This is a quick and dirty writeup discussing the Rock Band 4 drum kit on Xbox One and how to mod it for use with an MIDI capable e-drum kit. The TLDR is that it mostly works, but I can’t compensate for the deficiencies in the RB4 kit’s firmware, so, until Harmonix releases a fix, you’ll be stuck with the lag and possible dropped notes inherent to the current firmware.
As a note, old controllers apparently work just fine on the PS4 since they have a more open standard for allowing peripheral connections. However, my entire Rock Band catalog is on Xbox One, so that’s a no go.
The basic schematic for this is:
Drum brain -> MIDI trigger (powered by USB) -> Level shifters -> RB4 Drum Kit
You need to remap all MIDI notes on your drum kit so that any single pad triggers the the same MIDI note regardless of whether it is hit on the head/rim/edge. You should also take care of crosstalk and any other relevant settings on the brain as well. The MIDI out should connect to the MIDI trigger input.
Previously in Rock Band 1, I used a board from Highly Liquid called the MSA-P to trigger output signals from MIDI notes. Highly Liquid now has a more advanced and USB programmable version called the MIDIWidget. I ordered it with the terminal blocks pre-soldered and some MIDI ports to attach later.
The MIDI Widget should be powered via a micro USB cable.
The terminal outputs of the MIDI Widget will feed into the level shifters. In addition, the 5V out from the MIDI Widget will power the level shifters and can optionally be used to power the RB4 kit with the help of a 3.3V voltage regulator.
MIDIWidget ($60) + Terminals ($20) + MIDI ports ($7) = $87.
As far as configuring MIDIwidget, see below. It’s important to set the Logic to Note On: Fixed Duration as a nearly instantaneous MIDI signal is confusing for the drum kit. I set the output duration to 25ms for all outputs, but it’s possible a different duration might be appropriate. Also notice that the first output is inverted due to it being the kick pedal, which needs to pull down to ground from 3.3V to be triggered (see more on that down below).
The RB4 circuit board runs primarily at 3.3V. The output signals from the MIDIWidget are 5V. While we might be able to get away with that, for correctness, let’s use some voltage translators. I purchased some generic ones off Amazon since I wanted them right away, but if I had a few more days I’d probably order this 8-channel Bi-directional Logic Level Converter from Adafruit.
Cost = $8.00
Rock Band 4 drum kit
From the level shifters, you’ll need to connect to the eight signal pads I’ve identified on the main RB4 drum kit controller board, as well as 3.3V and ground. This will require tearing down the kit, which I outline below.
Screwdrivers (preferably some that are reasonably lengthy since some of the screw holes are deep.
Soldering station and solder
A spool of 22 gauge wire and wire strippers.
Some breadboards to help prototype everything.
Hot knife – to remove the controller portion of the kit. I used the Weller WSB25 – Amazon link.
RB4 drum kit teardown
The primary drum pads on the RB4 kit (red/yellow/blue/green) appear to have piezoelectric sensors that are connected to jumpers on the main board. The signal from the pads is amplified (presumably to a peak of 3.3V) and then passed on.
In game, the four drum pads can also be triggered by pressing the front buttons of the controller. Unfortunately, while it was easy to access the controller button solder points on the RB1 drum kit, there is no obvious way to do this on the RB4 kit.
Initially, I thought I was going to have to do something funky to simulate the piezo sensors (which are in the millivolt range). However, after further examination, I realized that Mad Catz left some bare test pads next to each drum pad jumper that expose the point right after signal amplification and before it reaches the signal processor for the kit. So we can simply pull up each test pad to 3.3V to trigger the respective drum. Note: I am not going for any sort of velocity sensitivity in this mod.
Cymbals and kick pedal
The cymbals for the RB4 kit attach to the back of the kit. There is a small circuit board here that attaches to the main board via a ribbon cable. It appears that the piezo amplification is happening on the peripheral board and simply comes back to the main board via the ribbon cable.
Triggering the cymbals works just like the drum pads. We simply need to pull up each cymbal connection point to 3.3V.
The kick pedal works differently from the other pads. Like the cymbals, it also has a small helper board at the peripheral input point that does the signal amplification. However, at the main board, instead of poking the connection point with a 3.3V signal, the kick pedal is activated by pulling the kick pedal’s 3.3V line to ground. To account for this, the MIDIWidget output for the kick pedal needs to be inverted.
3.3V and ground
As noted above, the 3.3V line is important. I take ground from the negative terminal of the battery, and I take 3.3V from one of the solder points for the cymbal ribbon cable. Note that the positive terminal from the battery is unregulated power, usually in the 2.4V range. So you don’t want to use that. You should also connect the grounds from both the controlelr and the MIDIwidget together.
It should be possible to completely self power the controller via the MIDI Widget by feeding the 5V out to a 3.3V voltage regulator, and then connecting that over to the positive battery terminal. Obviously, you must remove the batteries if you do that. Update: I did end up doing this and it works perfectly.
General comments and conclusion
I was rather pleased that I got this all to work, but then I realized the Rock Band 4 drum kit itself has actual serious problems. In particular, it’s adding 100ms of latency and possibly dropping fast notes on the drum pads and kick pedal. Context: regular e-drum kits have about 3 to 4 ms of latency.
How do I know the lag is this bad? It’s honestly so bad that simple observation is all you need. Also, in comparison, pressing the front face buttons has almost no latency at all. If you calibrate with the buttons via the pads, the difference is quantifiable and I’ve run it several times to confirm the difference.
We know that the Xbox One team worked specifically to reduce latency in the wireless controller, so the latency coming from the RB4 drum kit is unnecessary. There’s nothing special about the game that requires it.
Sadly, I can find no easy way to trigger the front buttons as a substitute for the drum pad sensors, short of soldering over the button pads. At any rate, there is no obvious equivalent instant button for the cymbals/kick.
Is the latency coming from the Rock Band software itself? Probably some, since the community hasn’t been able to calibrate A/V lag below 100ms. But considering the buttons vs drum pad hits show a large difference in latency, it can’t be the only factor.
So what are my outs on this? It’s possible there’s more that can be done with the surface mounted controller in the middle of the circuit board that would possibly allow zero lag triggering (ala the face buttons), but the solder points for that are so tiny that manually soldering to them is nearly impossible. It’s probably easier to hope/wait for a fix. The other option is to buy an old RB2 or RB3 controller along with a legacy adapter and mod that.
Whoever programmed the chip that is processing the incoming signal from the drum pads has made a horrendous mistake. If this lag is not fixable via a firmware update, the controller is basically junk.
Having spent quite a bit of money and time on this hobby, I’m extremely disappointed in Harmonix for releasing defective hardware. With this mod, I can play along with the game right now and it is enjoyable, but it is not as pleasant as Rock Band 3 was. All I can do now is wait and hope a fix is forthcoming.